Ceramic Ferrules: One & Two Piece

Blasch ceramic ferrules provide more effective waste heat boiler tube protection and allow for much greater design flexibility than traditional refractory systems. This is accomplished through the separation of the structural and insulating functions of the ferrules.

There are several options available, depending on the specific details of your particular equipment. Operational advantages of our precast ferrule systems include:

• Thermal Management System (TMS): TMS is a pre-fired tubesheet protection system that allows for the extensive use of fiber insulation in conjunction with the ProLok two-piece ferrules and provides greater insulating value than castable alone, in a greatly compressed area, saving space, and refractory.
• Improved performance: Large expanses of castable refractory undergo tremendous thermal and mechanical stresses as they heat up and cool down, which results in cracking in the castable refractory. Tubesheet protection systems consisting of our precast two-piece ferrules perform with built-in expansion joints, limiting damage to a confined area. 
• Reduced pressure drop. Blasch’s ProLok ferrules are available with a wide range of tapered inlet and outlet profiles. In addition to reducing the refractory mass in the furnace, ProLok ferrules have been shown to reduce pressure drop over conventional round ferrules and castable installations.

Patented Ferrule Design Leads to Reduced Peak Heat Flux

At the 2017 Brimstone Vail Conference, Clinton Schulz of CITGO Refining and Chemicals presented results that his plant has realized utilizing a patented ferrule design which was engineered in cooperation with Blasch in 2005.

Download his full paper to find out how patented modifications to the Blasch Ferrule design have resulted in longer boiler tube life due to reduced peak heat flux.

CITGO – US Patent #7,574,981
 

To find out more, download the full paper as presented at Brimstone Vail.

Ease of Installation

Patented Blasch boiler tube ferrules are pre-engineered for each and every boiler tube installation. Customers can expect to receive ferrules that are properly sized, accurately molded, and completely wrapped with all required fiber insulation.

Installation is as simple as taking them out of the box and slipping them into the boiler tubes. Castable refractory is not necessary between the ceramic ferrules and only the most minimal amount is required around the periphery. Operators can save days on turnaround without the need to painstakingly install, and then cure out, large expanses of castable refractory.

Two-Piece Ceramic Ferrules

Our patent-pending ProLok™ twist and lock two-piece ceramic ferrules have several advantages over traditional one-piece systems and offer increased reliability over traditional two-piece ferrules.

• Increased Thermal Expansion Tolerance: By separating the ferrule’s head and stem, stress is removed from the concentration point where the two connect in a one-piece design, allowing for better thermal expansion tolerance.
• Improved Design Means Longer Life: Sinking the stem deep into the head reduces stress on the stem by decreasing its length, also allowing the head to pivot slightly around the stem. This flexibility allows the ferrules to better accommodate warped or out of spec tubesheets while also allowing the ferrules to naturally adjust to each unit during start-up, with each ferrule having the ability to independently shift into the ideal position.
• Patented Twist And Lock Design Keep Ferrules In Place: With other two-piece ferrule designs, you run the risk of having the stems fall out of the tubes during service. Our ProLok twist and lock design address this concern by utilizing a locking mechanism. This lock retains the flexibility of the ferrule while ensuring that the ferrule stem does not separate from the head while in service.
• Superior Material Properties: With a wide range of high alumina compositions available, Blasch is able to offer exceptional resistance to corrosion, erosion, and thermal shock. Additionally, these two-piece ferrules are fired under controlled conditions in a plant environment, resulting in consistent, predictable properties; rather than ferrules that require the extensive use of castable refractory and field curing. Due to its design, ProLok two-piece ferrules are not subject to the vagaries of weather, installation expertise, and time constraints.

Other precast boiler tube ferrules are designed to be installed with some amount of protective barrier consisting of mortar between the ferrules which creates a problem when ferrules heat up and expand. The mortar is crushed during this expansion and can fall out after repeated cycles, leaving a direct path to the tubesheet. Blasch ceramic ferrules for boilers are engineered to come to closure at operating temperature without the need for this secondary protective barrier.

Request a sample ProLok Ferrule

US Patent #8,646,515

Product Information Sheets